ຂ່າວ

Problems Needing Attention in the Use of Fully Automatic CNC Wood Lathe

Problems Needing Attention in the Use of Fully Automatic CNC Wood Lathe

2022-07-22 11:29:27

Heating causes of fully automatic CNC wood lathe

 

If the full-automatic CNC wood lathe is used for a long time, some abnormal heating will inevitably occur. What is the reason for this? What measures should be taken to solve the problem of a fully automatic CNC wood lathe?

 

  1. It may be that the fuselage is overheated. To reduce the internal heat, it is necessary to increase the power of the engine cooling fan as much as possible, and at the same time, it is necessary to clean the dust off the cooling fan in time.

 

  1. It can increase the heat dissipation of the full-automatic CNC wood Because the machine is symmetrical left and right, the spindle of the heated double column mechanism will not only translate in the vertical direction but also have little deformation in other directions. The movement of the shaft in the vertical direction can be easily compensated by coordinate correction to increase the heat dissipation of the machine.

 

  1. It can also directly cool the heated parts, which can be achieved by splashing water and cooling fans. The thermal deformation of the shaft occurs in the vertical direction of the tool, which can reduce the impact of the thermal deformation of the spindle on the processing diameter. It can also heat the temperature of the parts at the bottom so that the overall temperature of the full-automatic CNC wood machine tends to be the same.

 

CNC WOOD LATHE

 

What problems should we pay attention to when using a full-automatic CNC wood lathe?

 

During the operation of the full-automatic CNC wood lathe, do not touch the running machine parts and processing parts with your hands, nor put your hands on the moving parts that are easy to contact the fixture to adjust the wood lathe or sort out the debris and sawdust. If necessary, you can cut off the power first and stop the machine before finishing.

 

The exposed part of the full-automatic CNC wood lathe in the energized state may be the source of danger and personal injury. Any direct or indirect contact will lead to accidents. When the full-automatic CNC wood lathe is overhauled, the external power supply should be cut off, and the input end of the power supply should be attended to. The maintenance of the machine needs to be operated by a certified electrician. Blind experimental maintenance may lead to the expansion of the fault area and bring more trouble to the later formal maintenance.

 

Maintenance of fully automatic CNC wood lathe

 

Given the risk of wood, a rebound in the wood processing operation of the full-automatic CNC wood lathe, protective feeding equipment, or a separation knife is required. The full-automatic CNC wood lathe should be equipped with protective control equipment requiring an emergency stop at the end of the machine while installing the normal start and stop operation equipment, to avoid injury to the human body.

 

When sanding with sandpaper, the tool holder should be removed before sanding. When the lathe rolls, it is not allowed to use a hand brake. Before wood is processed on the lathe, it needs to be processed into a cylinder. Wood with knots or cracks should not be cut by the lathe. When the full-automatic CNC wood lathe works, the speed will gradually increase, and the temperature of the tool will also increase, which will more or less bring physical and mechanical wear to the tool. If the input and output are too large, It will also cause wear and tear to the props, so when operating it, you should control the speed of the machine.

 

Searching for a cnc automatic wood lathe, cnc automatic wood lathe machine, cnc lathe machine wood supplier, wholesaler, manufacturer from China, you can get high-quality products at a nice price.

ຕິດ​ຕໍ່​ພວກ​ເຮົາ
ຊື່

ຊື່ can't be empty

* ອີເມວ

ອີເມວ can't be empty

ໂທລະສັບ

ໂທລະສັບ can't be empty

ບໍລິສັດ

ບໍລິສັດ can't be empty

* ຂໍ້ຄວາມ

ຂໍ້ຄວາມ can't be empty

ສົ່ງ